Windows Support Forum

Z600 Bios Image Corrupt - ROM flash doesn't work

Q: Z600 Bios Image Corrupt - ROM flash doesn't work

I have a Z600 that came with an REV #003 motherboard and two X5670 CPU's. The board went bad and I replaced it with a REV #001, not realizing that it won't run X56xx chips. So I then purchased two X5570 CPU's and put them in. When I boot, I get a series of 8 beeps, and an error message that the BIOS is corrupt. So I created a BIOS recovery disc and flashed the machine as per the instructions. I then unplug the power cord (as opposed to powering down first), wait 5 seconds and plug it back in a power up. I then get the 8 beeps and the error message just like nothing has been done to fix it. Is it possible that trying to run X56xx chips on that board fried something? Is there a way to reset it? What should I try next? Thanks.
Relevancy 100%
Preferred Solution: Z600 Bios Image Corrupt - ROM flash doesn't work

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link (This link will automatically start a download of Reimage that you can save to your computer.)

Relevancy 70.09%

the problem is that i can't see any flashes on any site. for example i go to ed test site. i can't see their meters!. i go to chatting site i can see nothing. just a small icon on the top left side. i d/l macromedia flash 8 . still no difference.

wat is the problem where have i go wrong??
is this a software problem or ??

any useful help really appreciated.

A:Flash doesn't work on Flash enabled websites

Please use proper thread titles from now on.
Relevancy 68.8%

I recently updated the bios on my EVGA 790i Ultra SLI board to the latest version. After restarting the computer, I cannot get windows to start "Bootmgr image is corrupt" or "The file is possibly corrupt. The file header checksum does not match the computed checksum."

I put in a the windows 7 64 bit disk to try and boot from it, and i get to the setup menu. I try to choose Launch Startup Repair (recommended) but the system keeps going back to the WIndows Error Recovery, and will not get into any setup mode. I try to launch normally but it keeps restarting itself.

I have 2 striped raids, one has the windows drive, and one with other various files.

I have an option in my raid setup to clear mbr, but i dont want to lose my data, is that going to mess up everything even more?

A:BOOTMGR image is corrupt. after updating bios

I think i fixed it. I should have reset the bios defaults after flashing. Then enabling raid, and changing boot priority, adjusting timing, multiplier and voltage.

Next step, backup everything on my raid 5 array.
Relevancy 67.51%

I had a zip of an Nero NRG image, When I went to extract it I was given a corupt error. I used Advaced Zip repair on it and it said it was fixed. I tried to burn the image with nero and it say it is not a valid NRG image. How can I salvage, change, or burn this repaired NRG image with nero or another program. Thanks
Relevancy 67.08%

Hi everybody i need your help i have hp z600  workstation but when start doesnn't show anything i change procesor  ram graphic card but same problem  didnt show anything in scren can anybody know what is to happen with my pc ? 

A:HP Z600 Workstation doesn't show anythink

Do the system fans start to spin after you hit the power button ?Does the workstation not beep and blink red ?
Relevancy 66.22%

If this is in the wrong forum I apologize My brother has a Toshiba Satellite I had the model written down but I lost it I can get it from him again if it is needed I think it has one of the the AMD x CPUs with the graphics build into the CPU if that helps It came with Windows He cannot boot anymore He said he sent it back to Toshiba when it was still under warranty but they told him it was not a hardware issue So the question is what to do next Since Windows and factory do 7 What if doesn't work? you do corrupt restore is he cannot do a factory restore I was thinking he should order What do you do if Windows 7 is corrupt and factory restore doesn't work? a restore disc from Toshiba I m surprised they did not advise this to him in the first place He has the Windows sticker on the computer but is it even possible to order a Windows install disc without paying for the full version I What do you do if Windows 7 is corrupt and factory restore doesn't work? suppose I could burn a linux CD for him I quot m pretty sure the hardware is working because he said it tries to load Windows but it cannot finish nbsp

A:What do you do if Windows 7 is corrupt and factory restore doesn't work?
Relevancy 64.93%

Trying to address a different problem Gigabyte suggested that I update the BIOS on my GA-F A X-D H mb from F to F In addition to not solving update BIOS Image after fill doesn't screen the problem Image doesn't fill screen after BIOS update after I updated the image displayed on my monitor--Dell WA--doesn't fill the screen Everything's there but the image stops about quot short of the right bezel Using AMD's Catalyst Control Center hasn't worked I've read some posts about a similar--the same --issue that suggest changing a setting in quot My Flat Panel Display quot But I see only quot My VGA Display quot with no option for over- or under-scanning The image does display Image doesn't fill screen after BIOS update fully on rebooting--I see the Gigabyte UltraDurable logo and on entering BIOS instead of going into Windows -bit Any thoughts Since first writing this I've tried the monitor's menu and other buttons without success Is it worth getting a DVI-D to DVI-D cable to connect digitally in place of the current VGA connection Does it signify that the monitor reports a screen resolution exceeding its supposed maximum of x namely x In both Windows screen resolution and AMD CCC I'm unable to set a resolution above x and setting lower resolutions doesn't help

A:Image doesn't fill screen after BIOS update

Hi David

Dated but might work for you:


Link 2 (Microsoft)

Keep us posted and Happy New Year
Relevancy 64.93%

Asus H Pro is the Motherboard and I thought that is a good idea to update the bios after that I've see update BIOS I the usb 2 EZ Asus continue doesn't flash can't realised that was not I've copied the Bios update file H -PRO-ASUS- cap to a GB flash FAT and hit update After the progress bar rich the end I restarted following the bios update dialog At Asus EZ flash 2 doesn't see usb I can't continue the BIOS update this point all I have it's a black screen with the USB flash plugged in or If I remove the flash I can access the UEFI but there is a single option quot to finnish BIOS update you have to select the same BIOS file cap file again to continue updating the BIOS quot sounds good enough but If I hit OK and choose via Storage devices option EZ doesn't Asus EZ flash 2 doesn't see usb I can't continue the BIOS update see the flash I've read about the size of the flash and I've shrinked in cmd to MB formated again to FAT and Asus EZ flash 2 doesn't see usb I can't continue the BIOS update after that I've copied the cap file Unfortunately the same result the flash is not available using any of the USB mobo's ports Anyway there is no SSD HDD optical drive plugged in Not so sure about the indicated File Path fs where it is more exactly and if matter The stick should be bootable There is a second option using the internet but I don't have wifi and if I plug the Ethernet cable first I have to communicate the MAC to the provider which is not possible as far as I know at this phase in order to make it available Any advice I appreciate it
Relevancy 64.93%

Hello everyone I've browsed everywhere on the net and all I find is people saying that Adobe creative suite CS works on Windows x Well it does except one part Flash CS I was wondering if anyone found a work around to this I have already tried running in XP compatibility mode and no luck I really don't want Doesn't work Windows Flash with CS4 7 x64 to use the x version of windows as I'll lose gb of ram in the process and definitly don't want to dual boot as i'm usually just doing things on my computer and randomly see my flash icon and decide I wanna do a little programming in Actionscript for a half hour or so Yes I know I can get Flex or another IDE however I like the convience of in Flash CS as inferior as it may Flash CS4 Doesn't work with Windows 7 x64 be to Flex of hitting ctrl enter and my program is compiled and running in front of my face instantly I generally compile once every mins to test changes I Flash CS4 Doesn't work with Windows 7 x64 make while programming so the Flash CS is best for me as I'm a fairly new programmer and I only know actionscript as of right now Has anyone been in a similiar situation or gotten flash CS to work on the bit version of windows TBH i don't even know if flex works on windows i've never tried it lol but again the problem with me enjoying instant compiles is why I'm trying to get Flash CS to work in the first place so it really doesn't matter if flex works or not Anyway thanks for any help

Relevancy 64.93%


When I go to myspace, instead of getting the music player, I get a box that says "Get Flash now!" and that I need to upgrade my flash player. So I go and do that, restart the browser, restart the computer, go back to myspace, and it still says that. So I check to make sure I have the latest version of flash and the macromedia site says I do have flash 10,1,53,64. I've tried this first on firefox, then chrome and internet explorer, but no luck on any of them. Oh, and my OS is 64-bit Vista.

Any help would be greatly appreciated.


A:Flash Doesn't Work in Myspace

Anyone have any ideas?

Is this the correct forum?
Relevancy 64.93%

I am having problems playing flash content in web pages Youtube videos do not show up StubHub s interactive map doesn t appear Web Sites that use flash advertisements don t appear Video content on many news sites such as MSNBC doesn Playback Work Doesn't Flash t work I ve been searching Tech Support Flash Playback Doesn't Work Guy on this topic for some time but have been unable to find any issues similar to mine The machine in question is my work machine so I m fairly upset that the problems I m experiencing will interfere with my job I have the latest versions of Flash and Shockwave installed When I visit the Adobe test page for these software packages the animations play perfectly verifying that they are installed succesfully I primarily run Chrome but also use Firefox IE and a standalone IE I work in software development so many browsers is essential I have an ancient version of Opera on the box I never use I m running Windows XP and all my software is up to date So far I have tried uninstalling and reinstalling Flash from Adobe s web site I have done this many times and upgraded when a new version was released I ve been struggling with this for many weeks At first I thought the issue was Chrome itself so I uninstalled and reinstalled Chrome as well I ve also uninstalled Firefox COMPLETELY Including removal of local settings Any insight or assistance with this would be much appreciated nbsp

A:Flash Playback Doesn't Work

No help :-(
Relevancy 64.93%

I have an HPV100W flash drive and it doesn't work in my Windows 7 x64 laptop. I think there are three files that need to be in the Windows\System32 folder but I can't remember what they are. Can anyone tell me what they are?


A:Flash drive doesn't work

Check Device Manager for any yellow flags under the USB section.
Relevancy 64.93%

I don't know much about a flash drive but we have one plugged into one of my front USB Ports on my PC. When I tried to backup my work onto it I got a pop up saying that the F drive isn't ready to receive data. I pulled the flash drive out and reinserted it into another front USB port to see if it would work, but no. Can someone tell me if this is what happens when the drive is full. I have a 2G "Attache" Flash Drive and I've stored my Quickbooks info on it. Is there some directions I can follow to see if my front USB Ports are working, or is it the flash drive that is the problem?
Any thoughts? I need some step by step directions to follow.

Relevancy 64.93%

Hi everybody,

I'm new to Win7 (64 bits build). Everything worked fine until yesterday. For some reason Flash contents (videos, etc.) cannot be played anymore, either on Firefox or on IE8. No error message is showed, the browser just freezes.
I have updated both browsers and the plugins, but the problem persists and I have no idea of what to do.
Any suggestion?

Thanks in advance.

A:Flash doesn't work on Win7

It's because there is no 64bit flash yet.
Relevancy 64.93%

helloI use Flash Disinfector FD since over years on many computers Just now I'm trying install FD on laptop with Vista HP bit only for your information cos I'm sure it should work on this system I have downloaded newest wersion of FD undameged it install on other machines or in Virtual machine - Virtuaal Box - too When I double-click on Flash Disinfector exe system should display popup message advicing plug USB drive into and kill processes with taskbar After some seconds explorer exe if all gone well should appear again and Finish - Done popup message should appear In background hidden autorun inf folder is created Flash work doesn't Disinfector on root drive This sequence occurs in normal mode - when all operations OK - but here is not that good When I double-click Flash Disinfector exe my cursor change with ring icon system is in quot thinking quot mode lol and nothing popup appears Whed I looked more depth inside with Process Explorer I saw nircmd exe and pv exe subprocesses started but after - seconds dissappeared Nothing No popup no message no autoruns inf folder on C I even disabled NOD in installation time - nothing later Flash Disinfector doesn't work uninstalled it - same nothing

Relevancy 64.5%

I went away for the mouse doesn't missing desktop icons, Corrupt work. files, weekend and when I came back and turned on my computer there were a ton of problems seemingly out of nowhere On startup it displayed the quot Windows failed to shut down normally quot screen which was strange because I had shut it down normally before leaving and nobody else could have used it So I clicked quot Start Windows normally quot Then when it got to the desktop there was immediately an error of the ATI catalyst control center and also quot Corrupt files, missing desktop icons, mouse doesn't work. MOM exe - NET framework initialization error unable to find a version of the runtime to Corrupt files, missing desktop icons, mouse doesn't work. run this application quot When I tried opening Google Chrome it said that some part of the application was corrupt same with GNotifty My AVG antivirus was also marked with a caution sign saying quot you are not protected quot Hoping it was just a fluke I restarted and Windows presented me with the option to do a Startup Repair during the boot which I did It ran for about mins and then loaded to the desktop to present the same errors only this time there are desktop icons missing randomly and the mouse doesn't work I tried changing USB ports for the mouse as well as trying another mouse and it still doesn't work Next impulse was to run memtest from a bootable CD so I tried opening my optical drive and strangely it registers the button push and displays a green light but just doesn't open Stuck for what to do now Does anyone have any ideas on what the heck is wrong As far as I know there's no virus or malware problem I update and scan with AVG Malwarebytes and Spybot almost every day and don't download porn or torrents or anything Things were all fine the last time I used the machine a couple days ago And it is password locked so no roommates could have used it or anything

A:Corrupt files, missing desktop icons, mouse doesn't work.

is this vista or win7?
try starting the computer while tapping the f8 key, when the new screen comes up, using the arrow down key find "last known good configuration">enter, see if that does the trick...

good luck
Relevancy 64.07%

I have laptops that have windows installed and one with windows Recently I had another computer that the hard drive went out I went ahead and figured since most of my computers are new I would make system images of them if they ever crashed and if I had to replace the hard drives in them Well on every windows machine I have the Image option not System work? Why doesn't I have tried to make a system image to a GB nbsp dvd-r disc using the system image option under file history via the control panel What happens is I click the system image option it loads files but when I am prompted to label a disc and insert it I click the ok button it runs for a few seconds and says their is an error I keep getting the same dialog box over and over that says label and insert a disc and then it doesn't create the image Is there a certain type of DVD-R you are suppose to use or a certain way to format them My windows machine worked great in making the system image backup It took discs and when my hard drive went out I was Why doesn't the System Image option not work? able to restore the system image nbsp Not one windows machine I have does the restore or refresh option work because of the upgrade to and now the Why doesn't the System Image option not work? system image doesn't even work These options are the essentials to fixing your computer without having to download the drivers from the companies website and even then you may not get all the software or drivers needed Any suggestions because I am getting ready to scrap any windows pc and go with Why doesn't the System Image option not work? a Linux distro and buy an apple and get the windows office that can be installed on them and just do away with windows all together Its really gone down hill
Relevancy 64.07%

Hello everyone.

I use both the Chrome and Firefox web browsers, and I noticed that when I went to go and download flash player on firefox that it doesn't load the page to download adobe flash player. Is it not supported in Windows 10 as of yet? There are some things I cannot do in the firefox browser because of it.

A:Adobe Flash For Windows 10 Doesn't Work?

Adobe combines Flash Player into Windows, similar to Windows 8.

I don't believe its supported at this time.
Relevancy 64.07%

I have a HP Pavilion 754n that runs on windows 2000 Xp home edition . I recently had to upgrade my flashplayer to Flashplayer 9 . I get an incomplete download . I uninstalled my old version and tried toinstall the new version and it still doesn't work. What can I do? One time I downloaded it from comcast which said download complete but it still didn't work. Help!

A:My Flash Player downloads but doesn't work

You might need to run the Flash Player Uninstaller. Then re-install Flash Player.
Relevancy 64.07%

Hi, I'm having an issue with Microsoft Edge Flash not working, specifically on Pandora. I want to like it so much, it's close but it's missing some key features and various annoyances.

Anyways, Adobe Flash works just fine with Microsoft edge.

I have tried the solution to "Reset_Microsoft_Edge" via Windows PowerShell Command, which didn't solve the issue. (Also reset Internet Explorer's settings)

And Yes, before you ask, it's turned on in the settings.

What's very odd is that Pandora doesn't even use flash on other browsers, but it uses HTML 5.

YouTube Loads HTML 5 Videos in Microsoft Edge too, so I'm not sure what the problem is....

To be honest, it's a minor annoyance, Surely I can just use another browser, but that's bedside's the point. It's not working as it should, and I just want it fixed.
Relevancy 63.64%

Here is BIOS doesn't work my problem my computer worked perfectly until I connected an external hard drive via usb port Right after that I noticed a smell from that enclosure - smell of burning electronics But computer recognised an extra hard drive but couldn t open any folder I thought that that hard drive is burned replace it with other HD but was the BIOS doesn't work same although without any smell my computer still couln t open any folder And then strange things happened I disconnected that external drive and restarted the system to discover that only part of bios was loaded until searching for drives OK - I restarted again and nothing Black screen no bios no sound from HD I thought HD failure so I bought new HD installed and still nothing I installed the old HD to my spare computer as a slave and it works so the problem must be the bios I think so I visually checked the motherboard - it looks fine all fans are OK too So what next to do P GHz GB two HDs Vista Business AS Rock MB thanks for any help nbsp
Relevancy 63.64%

Hi, new to forums! I got about 3-4 year old Pavilion dv6-2137eo. I was installing some updates, and then it suddenly stopped working. I got black screen and nothing else. And now, whenever i try to power on it, ok it starts, but then it flashes num and caps lock light 2 times, 2-3 secs and again 2 times. I know it means BIOS failure, but i don't know how to fix it. Anybody please help! Thank you!

A:Pavilion dv6-2137eo doesn't startup, BIOS error flash code

Hi there @Nuu5kamu1kkun3n?, Thank you for joining in on the HP Support Forums and Welcome! This is a great place to ask questions, find solutions and get help from others in the community! I read your post on the HP Support Forums. I wanted to reach out to you and help! I understand that you having an issue with blinking LED's on your HP Pavilion dv6-2137eo Entertainment Notebook PC.  Please note remove any and all USB devices. Disconnect all non-essential connected devices, as these, could cause some issues. Try to start your Notebook normally after you have disconnected everything. If that does not fix the issue, please continue with troubleshooting.  The next step would be for you to try to Restore the BIOS. You will see that the document says:  If the BIOS on your notebook becomes corrupted, such as from a failed BIOS upgrade or damage from a virus, the computer might show any the following symptoms: The computer displays the error message BIOS APPLICATION ERROR 501.The computer stops at a black or blank screen and it will not enter any of the Boot Options, such as the BIOS Setup Utility, Hardware Diagnostic Tools, System Recovery screens, etc.The computer does not boot and the Caps Lock or Num Lock LED blinks twice or the computer emits beep codes.The computer turns on, for example, the fan might spin, but there is no video on the internal display or external monitor and it does not boot into the operating system.If the computer shows any of the previous symptoms and it does not boot up, use this document to restore the BIOS. After you Restore the BIOS see if you can start the Notebook normally.  Please let me know if I answered your question by clicking the 'Thumbs up' if the troubleshooting steps in this post resolved the issue for you please click the 'Accept as Solution' button. This will allow other's who have the same issue to find the solution also. If you require further assistance, I would be more than happy to continue to help you. Please just re-post with the results of the troubleshooting.  Have a great day!
Relevancy 63.21%

My floppy does not work...So I was thinking maybe I could do this.
My ASUS support CD is bootable...could I just burn everything on this CD except the BIOS.rom to another CD and add the updated BIOS.rom to that burned CD? Then boot with the newly created CD and flash it that way?

I was thinking if it did not work I still could recover with the original CD.

I looked through the process for creating a bootable CD and it looked like I would have to jump through a lot of hoops...thought this way might just be easier...what do you guys think?

Relevancy 63.21%

I had Antivirus spyware load on my laptop the other day Immediately I checked Bleeping Computer from another laptop and followed the instructions for downloading Malwarebytes Anti-Malware having to download it onto this other laptop and transfer it across to my computer via a memory stick I changed the filenames as instructed and ran the full scan which identified around items which needed removing and removed them Now I can t seem to use Flashplayer I tried to run a Facebook application and it said quot Page should doesn't won't Antivirus removal, and 8 Flash load work now load after seconds If not you may need to upgrade your version of Flashplayer quot So I clicked on the link and downloaded the newest version I think However this does not seem to have worked I have tried to do this again several times going onto Adobe s site itself to try and download it and although it goes through what seems to be a proper download Antivirus 8 removal, now Flash doesn't work and won't load process it doesn t seem to be saving itself to the computer Does anyone have any suggestions as to what I should do

A:Antivirus 8 removal, now Flash doesn't work and won't load

Try the following: Adobe Flash Uninstaller then try and reinstall Flash Player.
Relevancy 63.21%

Hello. I formatted my USB flash drive in win xp and now eahc time I connect it raises a warning: "The USB device can run faster if you connect it to a usb concentrer". Before format this message don't appear. The USB anyway works in win XP but doesn't work in Linux, an before the format it does.
My usb is a GeeDom 512 Mb. Somebody knows how to solve this problem? I need mi USB because I pass data beetween PC's with Linux and Windows.

A:USB flash drive doesn't work in linux after format

reformat as FAT32 which is accepted by ALL platforms.
Relevancy 63.21%

Hi I have problem wih flash in IE10 Windows 8 doesn't work. I did all what I found in internet on adobe forums . I made all what adobe says active x filtering off , shokvawe plazer enabled , reinstalled using uninstaller and reset all includet folder manually. I will say that on chrome and firefox flash works fine only on IE10 I got error message "get flash player". I play poker and casinos and some poker clients are set up with IE and I can't open games.I see over internet that some people get this same issue but unfortunatly I didn't found one good answer which could resolve that problem.Please help me if someone can or had this problem and managed to make it work.I really made a hours of resarch and haven't found solution.

A:Flash player doesn't work in IE10 on windows 8

Have you installed Flash Player for IE as well as for Chrome/Firefox.  They are separate installs and so need to be installed separately in IE and in Chrome or Firefox (there is one version of Flash Player for all plugin based browsers).  If you have Flash Player for IE installed try resetting Internet Explorer - see below.
Close all Internet Explorer and Explorer windows that are currently open.

Reopen Internet Explorer.

Click the Tools button , and then click Internet options.

Click the Advanced tab, and then click Reset.

In the Reset Internet Explorer Settings dialog box, click Reset.

When Internet Explorer finishes applying default settings, click Close, and click OK. You'll need to restart your PC for these changes to take effect.
Relevancy 63.21%


I'm having some problems with running Flash videos in Firefox3.6 The previous versions (3.5 and below) are working OK.

I try to run a youtube video inside a iframe on a chrome window:

var features = "chrome, top=0, left =50, outerWidth=500, outerHeight=500";
var url = "file://C:\\test.html";
var myWindow =, "mytest" , features);

The contents of test.html:

<iframe src ="">

The above code doesn't work in 3.6, but does in 3.5. Any ideas?

Thank you!
Relevancy 63.21%

my system have a problem when i copy data from pc to flash drive cannot work. display msg you'll need to provide administrator permission to copy this folder.

A:doesn't work copy and paste from pc to flash drive

Hi @HP193, Thank you for visiting the HP Support Forums. I have looked into your issue about your HP Notebook and not able to copy due to admin permissions. It is also possible to modify permissions. Try to enable the Administrator Account on Windows. I found this example it is a third party site and not affiliated with HP.  Please get back to me. To show that you like, or are thankful of my post, kindly click the Thumbs up below.  Thanks.
Relevancy 63.21%


I started using my laptop again and came across a website that needed flash player 7 to work. So I did the usual and went to the website and downloaded the latest flash player etc etc.

I then went back to the website and it still said I needed flash player 7 for it to work. I thought, what the heck is going on. I uninstalled the current version and reinstalled, with no luck.

So, here I am asking if anyone can help, provide a solution to my problem.

My current specs:

Vista Ultimate 32 bit SP1
Intel Core 2 T5500 1.66 GHz

A:[SOLVED] Flash Player installs but doesn't work.

Did you restart your browser after you installed? If not, do so. It should work. Btw, the newest flash player is flash player 10. You did download it from this site right?
Relevancy 63.21%

Hi I have problem wih flash in IE10 Windows 8 doesn't work. I did all what I found in internet on adobe forums . I made all what adobe says active x filtering off , shokvawe plazer enabled , reinstalled using uninstaller and reset all includet folder manually. I will say that on chrome and firefox flash works fine only on IE10 I got error message "get flash player". I play poker and casinos and some poker clients are set up with IE and I can't open games.I see over internet that some people get this same issue but unfortunatly I didn't found one good answer which could resolve that problem.Please help me if someone can or had this problem and managed to make it work.I really made a hours of resarch and haven't found solution.
Relevancy 63.21%

OS win bit FF Version Flash Version Hi I've had this problem for they on flash and some work websites in videos in some firefox do doesn't a while now and have no idea how to fix this issue the flash flash videos doesn't work in firefox on some websites and in some they do player does work on youtube and on twitch tv and I think that on some others too but on facebook http southpark cc com and CNN and other news websites it doesn't work just wanted to add this is not video related only some flash elements like this website's and some other website I frequently use file attachment isn't working as well although it flash videos doesn't work in firefox on some websites and in some they do displays the button Chrome plays everything fine but I want to use Firefox I tried disabling and reenabling flash videos doesn't work in firefox on some websites and in some they do the flash plugin in firefox multiple times uninstalling and reinstalling of both firefox and flash I tried to disable the hardware acceleration of flash but it seems like the setting is not saved because everytime I uncheck the option it returns when I move between the settings tabs or close and re open the settings I tried disabling the hardware acceleration through adding DisableHardwareAcceleration to the Flash mms cfg in Windows bit C Windows System Macromed Flash Windows bit C Windows SysWOW Macromed Flash but it didn't help Please help me Thank you

A:flash videos doesn't work in firefox on some websites and in some they do

Hi LinkTree. Have you seen this Firefox link? Try also clearing your cache, cookies and history on firefox and see if it helps. Make sure also that you have the updated video driver version as sometimes it helps. Using Adwcleaner may also check for Adwares and toolbars installed and remove them for a more cleaner browsing experience. Try clearing your cache files : Free CcleanerIgnore the Registry feature of Ccleaner as it is not recommended or needed. Download Adwcleaner by Xplode from here.Click on Adwcleaner and hit the Scan button and will begin to search for PUP and malicious files. Once finished click the Clean button. Copy and paste the log on your next reply.
Relevancy 62.78%

I've used Dism /Online /Cleanup-Image /RestoreHealthin admin mode and it still says corrupted.

A:Dism /Online /Cleanup-Image /RestoreHealth doesn't work.

Try to use these commands in this order, it might take a while, quite a while:

Dism.exe /online /Cleanup-Image /StartComponentCleanup
sfc /scannow
Dism.exe /Online /Cleanup-Image /RestoreHealth
sfc /scannow
Dism.exe /Online /Cleanup-Image /StartComponentCleanup /ResetBase
Relevancy 62.78%

i upgraded my os from xp to win 7 there some programs on my image files which are not running fine on Win 7 like counter strike condition zero
please help

A:Image CD software doesn't work in Windows 7 was working fine in XP

Not all XP programs are 100% Win 7 compatible. Probably the problem with the game. Try running the game in XP compatibility mode and see if that helps.
Relevancy 62.78%

I am a newbie here. I am trying to access my grandson's science book online, but when I try to open the ebook, I get the error message: Alternate HTML content should be placed here. This content requires the Adobe Flash Player. Get Flash

I have tried accessing the Manage Add-ons and Shockwave shows up. I have tried turning off Active X Filtering and restarting IE11 (Version 11.0.35). The site works just fine using Firefox, but my wife doesn't like using Firefox. What do I do now??
Relevancy 62.35%

Hello as the title suggests my problem is this a few moments ago i was browsing on my computer and everyhting was normal then all of a sudden my keyboard started acting weird caps lock reversed when i clicked enter on facebook it wuold just skip a line instead of sending my messages I thought it was something minor so Password, doesn't Wrong bios work then I rebooted instantly As soon as I booted and saw my motherboards logo the screen Wrong Password, then bios doesn't work stayed there far longer than it should like a solid - seconds instead of - then I typed in my password but it said it was incorrect I made sure to try other languages even on screen keyboard but nothing I rebooted again only to realise my PC would not boot at all no motherboard logo no bios anything just a black screen my USB devices are not responding either I download stuff all the time and sometimes I disable my antivirus could it be something like that and if so whats the solution A few days ago I wanted to access my BIOS for something different but could not do so after the motherboard logo i would press f or f or del etc and nothing Wrong Password, then bios doesn't work would happen or a black screen in case it helps my Wrong Password, then bios doesn't work motherboard is GA-XA-UD I m using an AMD FX with an FX stock cooler gigs of corsair vengeance ram my psu is corsair GS watt and my GPU is sapphire radeon gb Any ideas nbsp

A:Wrong Password, then bios doesn't work

We cannot help with password problems as per the rules. It does seem that you may have some other problem as well. I would try the following;
1 System OFF, pull the pw connectors from ALL drives; both hd and optical.
2 Remove any add-in cards such as nic, sound, etc. Leave your video card installed however do make sure it is fully seated.
3 Clear cmos with the clear jumper. Note gigabyte does not use a jumper pe se. Gigabyte boards just have two pins that you momentarily short to clear cmos. If in doubt, read your mb manual.
4 Now pw ON and see if the board will complete POST ie you get a display and receive a msg regarding no operating system found. If the board does complete POST, shutdown and start connecting devices one at a time until you find the failed part. If it does not complete POST in the above config, then you need to start swapping parts with known good units; ie mb, ram, pw supply, etc.

I download stuff all the time, and sometimes I disable my antivirusClick to expand...

I would REALLY stop doing the above. You are just asking for a problem. If you must download stuff, use a linux machine. Linux is much less susceptible to a virus.
Relevancy 62.35%

I'm using a E6230 running BIOS A01. I want to update to the latest version, A16. The update process runs without error and reboots the laptop. However the BIOS version is still A01. I've tried updating from A01 to A02 as well: same result. I tried to update running both Windows and a USB drive with DOS. What do I need to do to install A16? Thanks!
Relevancy 62.35%

I have dell Inspiron 5559, I updated my bios to the current version but apparently my quickset isn't working. I tried to uninstall but it says "Your computer's Bios is outdated. Update your bios firmware to current version." I cant update the quickset too! What should I do?!?
Thanks in avd. ...

A:Quickset doesn't work for BIOS update.

We?re listening. We?ll surely check and assist you. We don?t like customer?s upset and inconvenienced We request you to share the service tag/express service tag, the name on the account and your email address through a private message, so that we can for specific drivers and update the same to you. To send a private message, click on my name and select ?Send private message?
Relevancy 62.35%

I'm trying to reinstall my operating system but my keyboard doesn't work in the boot menu, so I can't enter the BIOS. I've tried both a USB keyboard and a PS/2. I think it might be my mobo but I'm not sure enough to replace it. I've had problems with it in the past (I bought it out of box about a year ago, so it would make sense I guess) like the microphone jack and keyboard and mouse PS/2 ports not working, but the weird thing is that they used to work in Ubuntu when I was dual booting Vista/Ubuntu. I tried updating the chipset drivers but that didn't work.

Any ideas would be greatly appreciated! I really don't want to replace my motherboard but I guess I might have to.


P.S. My system specs are in my profile
Relevancy 62.35%

Hi there would be grateful for any help on a problem that has me completely stumped I have an AJP laptop that was running Windows ME I've recently upgraded to XP Pro The upgrade didn't go entirely smoothly until I updated the BIOS now R if that helps Hey BIOS work doesn't update, Monitor is since it XP? or presto XP Pro installs and runs like a dream Except that since the BIOS update the laptop monitor is not working properly when I power up I have a blank screen with flashing horizontal or vertical lines sometimes both together I've hooked up an external monitor which is fine and the laptop monitor 'flashing style' changes according to what I am doing suggesting that it is receiving information and trying to do something with it Device manager says everything is working properly I've updated the graphics card driver S Twister K And then I deleted all the programs I didn't need or could easily download again one day in case there were Monitor doesn't work since BIOS update, or is it XP? any conflicts Oh and ran a full virus check for good measure I've scoured the internet spoken to AJP support and tweaked everything I can think of I'm assuming that it probably isn't a graphics card problem since it all appears perfectly on the external monitor Should I be tweaking something in the BIOS or a system folder Any suggestions

A:Monitor doesn't work since BIOS update, or is it XP?

Double check that you got the correct bios update for your exact unit
Relevancy 62.35%

Hello everybody I recently have gotten computer parts and put together a PC after a delay in the mail I have received the graphics card and installed it into the tower before I got the card I was using the computer perfectly fine with the CPU graphics that are integrated so I know that all of my hardware works or did When I put in the graphics card there was an issue with it showing up on the monitor so I took out the Bios outside work of doesn't Keyboard/Mouse motherboard battery with guidance Keyboard/Mouse doesn't work outside of Bios from a friend and reset the CMOS and I have it displaying now with a HDMI to DVI-D When I turn the computer on it turns on and then turns off instantly after the fans and such start to go it does this once then fully turns on and I press the delete key to load the bios after that I load windows and when I get out of the bios all usb ports stop working mouse and keyboard stop and im stuck looking at the windows screen showing date and time and internet connection I ve been looking online and still am yet to find a solution because everybody else that has this issue can somehow access their desktop I can t When I load from the windows CD i get into the starting menu for loading the operating system but again no mouse or keyboard so I can t keep going from there I removed the graphics card which initially caused the problem upon start up it restarted times and then turned on in the windows loading screen where i was stuck before the keyboard LED s are lit up but the mouse is not the keyboard also does not work just the LED s Any help would be GREATLY appreciated and here is a list of my parts CPU - i Ghz MOBO - Asus Gryphon z RAM - GSkill ripjaw x - clocked at in the bios GPU - Asus gtx Direct CU II PSU - Corsair HX HD - WD TB black Keyboard - Razer black widow ultimate Mouse - Razer Taipan nbsp

A:Keyboard/Mouse doesn't work outside of Bios

Have you tried both the USB 2.0 and USB 3.0 ports for the keyboard and mouse? Maybe the USB 3.0 isn't working correctly due to drivers or compatibility with the Razer gear or drivers. Or can you borrow a basic USB keyboard and mouse?

I also see a BIOS update on the Asus website that addresses "USB Compatibility" and "System Stability" in another. If you do not already have the 1603 BIOS update you may wish to update it that one. You can update the BIOS through the BIOS itself, go into the Advanced section and use EZ Flash and load it from a USB stick; it must be extracted first though.
Relevancy 61.92%

I'm on Flash work runs doesn't Player Adobe sound program, then a friend's computer right now who uses a dropbox system which works in conjunction with a sound recorder The person record whatever he or she needs to record Adobe Flash Player runs program, then sound doesn't work they save it which means it sends to whomever the dropbox was made for which in this case is his her professor DAMN THEM PROFESSORS Usually he she tries to use the program and the sound recorder which works or doesn't work but causes all audio on the computer to fail When the friend came to me for help on a freak accident the microphone dropbox system worked and kept all audio intact and sound So I know the sound is working or able to work Another interesting thing about this problem is that ALL audio programs do not work This doesn't just affect the browsers this also affects Windows Media Player which now refuses to Adobe Flash Player runs program, then sound doesn't work play sound files that used to be able to be played because it says it can't play that kind of file Please help

A:Adobe Flash Player runs program, then sound doesn't work

Go to audio device manufacturer's site and see if driver updates are available.

If "SP1" in user name refers to Windows 7 SP1 Beta, I would suggest that you uninstall it.

Windows 7 Service Pack 1 BETA

Regards. . .


Relevancy 61.92%

I have windows 10 and recently updated Adobe flash to the latest version. This is where the problems began. While using an administrator account, pages that require flash in IE or Edge worked fine. But when logged on using a standard account, those pages say you need to download the latest version of Flash Player. In IE 11, Flash is enabled and ActiveX filtering is off, but Flash still doesn't work on a standard user account, but does work on administrator accounts.

This problem with using a standard user account only happens with IE 11 and Edge browsers. Adobe Flash works fine on standard accounts using Firefox and Chrome. Just wondering if others experience this.
Relevancy 61.49%

Replaced dead videocard with msi HD6450 and machine won't boot. Tried old card I had laying around and it works fine. My searches have turned up questions about BIOS / UEFI compatability problems but no solutions. This is the second card I've tried, I sent the first one back assuming the problem was with card.Motherboard: Angelica 1.2CPU: AMD FX-8150Bios: Ang_716      4/5/2012The original card was a GeForce 8500GTThe card I'm temporarily using is a GeForce 9300 GE
Relevancy 61.49%

System had WIndows upgraded to Win and then wiped and reloaded with a fresh Win install To try and fix the plugged in and not charging issue I installed the F Rev A firmware dated July nbsp nbsp System an work restore to BIOS the doesn't How upgrade when correct won't boot to WIndows says no OS installed nbsp When I switch to legacy mode I can boot slowly and run Windows nbsp I tried How to restore the correct BIOS when an upgrade doesn't work all the previous versions on the website but they all say they aren't compatible nbsp The ALT-B fix doesn't work to roll back the firmware nbsp I even did a full system restore of an Acronis True Image backup from pre- upgrade and it doesn't make a difference nbsp System didn't have the HP PC Hardware Diagnostics UEFI nbsp so I installed the version from the website but it can't find a version to roll back to and none of the versions on support seem compatible nbsp Can someone tell me where to get to correct firmware to load to fix this problem

A:How to restore the correct BIOS when an upgrade doesn't work

System info is: Product# E3508UA#ABLModel: 15-j078caRev: 1963-100
Relevancy 61.49%

Says " an operating system wasn't found. Try disconnecting any drives that don't contain an operating system. Press Ctrl + alt + delete to restart" black screen. "Admin" password does nothing.
Relevancy 61.49%

Hi, I've recenty updated the BIOS to F17 and after it was done, the display is connected to HDMI port doesn't display anything and it seems it doesnt detect! I've also updated both VGA drivers (Inter and NVIDIA), but I still have the same problem! Any solution to solve the issue? Any solution to downgrade the BIOS? Br,Meghdad
Relevancy 61.06%

PC has been running fine no issues,this morning switched it on and it when to boot as normal then went to a blank screen with message can not boot boot image corrupt
Since then,every time I tey to boot ,fans start then CPU fan stops monitor stays blanks and I don't even get the boot page
Press F5 or F8 does nothing and can't get into BIOS

PC about 8 years old with a giga byte EX58UDR3 mobo and Intel think it's a i27 CPU

A:corrupt boot image message ,now will not boot and cant access bios

It sounds to me like hardware failure. I'm not sure what that picture is for but I suggest that you check for blown capacitors. Capacitor Lab - Visual Signs of Capacitor Failure - Bulging and Leaking
Relevancy 61.06%

I've got a Windows 7 upgrade disc, so I first installed Windows XP and now need to boot from this new disc. Because I'm going from 32-bit XP to 64-bit Windows 7, I have to boot from the disc.

I can press F12 to get into the boot order selection screen; but pressing the arrow keys, escape, or enter has no effect. Once I'm on that screen, I just have to turn off the PC because I can't do anything else.

Both keyboards I've tried have been USB. I actually bought a new keyboard in case my keyboard was the issue, but the stores only had USB keyboards--if USB is the issue, I'll have to wait a few days before I can borrow an old keyboard that uses PS2.

Is there any way to workaround this using the USB keyboard I have?

A:Keyboard doesn't work in BIOS, any other way to change boot order?

Try plugging the usb keyboard into the usb port next to the ethernet port.

Relevancy 61.06%

Ok so I bought a HP Mini Notebook for my wife Model NR Everything was working fine She goes to boot it yesterday and she gets hit with a password right after the AMI bios screen She asked me if I set the PW I told her no and she said she didn t either No big deal I take it apart and unplug the CMOS battery for about minutes Hold the power button down for a bit to discharge any left over juice Put it all back together and Unplugging battery work. BIOS doesn't CMOS password. same thing So I tried to leave it out for over hours and the same thing I even tried various AMI master passwords I knew it wouldnt work but you BIOS password. Unplugging CMOS battery doesn't work. know how desperate we get So now I m stuck I googled it today and found various information Most leading me to believe I am stuck with a paperweight or will have to send it to HP to have it fixed which will run me almost what I paid for it So am I missing something here Anything else I can do Thanks guys nbsp

A:BIOS password. Unplugging CMOS battery doesn't work.

Well I can tell you that removing the battery will NOT clear a pw on a laptop. This is a security feature. Next we do not assist with pw help. This thread is now closed.
Relevancy 61.06%

Hi guys I've been at this for three hours I hope you can help and I'll get to the point - Need to access BIOS USB keyboard Logitech G not recognized until the Windows login screen loads - No PS ports and blast it I have a PS keyboard that I can't use Cannot get a USB- gt PS adapter at this time - I reset CMOS and disconnected the hard drive This produced two lines saying there was no boot disk did not drop me into the BIOS - HP Pavilion P model P f - I have no other USB keyboards available - The keyboard doesn't light up until the login screen The way these threads seem to go elsewhere is quot Can't get to BIOS with USB keyboard quot quot Okay change your BIOS settings to turn on legacy quot quot But I can't access the BIOS quot I'm trying not to purchase additional computer crap I accept that there may be no way to do this Thanks if you can help

A:USB keyboard doesn't work before Windows login (can't access BIOS)

Are you able to borrow a keyboard from a mate to test
Relevancy 60.2%

I bought my Satellite Z in August and installed GB extra RAM in it Worked fine the Ultrabook detected it and had total GB of RAM Yesterday I stopped ignoring these Toshiba Tempro messages and installed the suggested BIOS Update to Bios don't know which version it was before Now I have several problems First one my Ultrabook doesn't start anymore with the extra RAM I press the power button then the power LED starts blinking times yellow time orange in RAM work Update, doesn't anymore Satellite BIOS - Extra Z930 after loop The screen stays black and the CPU fan raises to maximum level Only when I remove the extra RAM then it starts Second problem without my extra RAM it starts but sometimes with Satellite Z930 - after BIOS Update, Extra RAM doesn't work anymore the CPU fan at maximum level So i have to restart that it stops Third problem Windows only detects GB of RAM I have now no extra RAM istalled so it should detect GB of RAM like when I bought it Now there are only GB So is this what happens when I install suggested updates - - So what can I do now At least I want my preinstalled GB of RAm back Is there any BIOS downgrade or something similar to revert the changes

A:Satellite Z930 - after BIOS Update, Extra RAM doesn't work anymore

OK, solved the problem. I found a BIOS downgrade to 2.1 at this page:
Now I have my 6GB back :)
Relevancy 59.77%

Hello all, After updating the BIOS to version A16 or A17 doesn't work memory card reader :(
On the aforementioned version of the BIOS, when you want to turn on the computer with a memory card inside the system do not get up! Of course, without a memory card system will get up normally but when you again put the memory card the system still can't see it.
The last working version of BIOS is A15 where you can use a memory card reader.
My OS: Windows 10 Pro (x64)

A:Latitude E7440 - memory card reader doesn't work after bios update

I have exactly the same problem. Last working version is A15.
Relevancy 58.48%

Pasting in contextual information from another post OBconflicker Bi nf worm keeps reappearing windows defender monitor stops working slow computer windows search protocol windows pop up Malware virusPop up windows keep appearing quot Windows search protocol host stopped working stopped, protocol search work, doesn't firefox work microsoft host windows slow, itunes doesn't and was closed quot Itunes occassionally doesn t work Media Sync doesn t work Hard Drive keeps working microsoft windows search protocol host stopped, slow, firefox doesn't work, itunes doesn't work in the microsoft windows search protocol host stopped, slow, firefox doesn't work, itunes doesn't work background Windows Defender no longer monitors the running programs End of added information microsoft windows search protocol host stopped, slow, firefox doesn't work, itunes doesn't work OBLogfile of Trend Micro HijackThis v Scan saved at AM on Platform Windows Vista SP WinNT MSIE Internet Explorer v Boot mode NormalRunning processes C Windows system taskeng exeC Windows system Dwm exeC Windows Explorer EXEC Program Files Windows Defender MSASCui exeC Program Files Digital Media Reader readericon G exeC Program Files Java jre bin jusched exeC Program Files Intel IntelDH CCU CCU TrayIcon exeC Program Files Common Files Intel IntelDH NMS Support IntelHCTAgent exeC Program Files Intel Intel Matrix Storage Manager IAAnotif exeC Windows WindowsMobile wmdc exeC Windows System hkcmd exeC Windows System igfxpers exeC Windows sttray exeC Program Files Windows Sidebar sidebar exeC Windows ehome ehtray exeC Program Files Google GoogleToolbarNotifier GoogleToolbarNotifier exeC Users Owner AppData Local Temp nkapg r exeC Program Files Windows Media Player wmpnscfg exeC Windows system wbem unsecapp exeC Users Owner AppData Local Temp smss exeC Program Files BullGuard Ltd BullGuard BullGuard exeC Windows system igfxsrvc exeC Windows system WerFault exeC Users Owner AppData Local Temp win exeC Users Owner AppData Local Temp csrss exeC Users Owner AppData Local Temp system exeC Program Files Intel IntelDH CCU CCU Engine exeC Users Owner AppData Local Temp Low services exeC Users Owner AppData Local Temp Low smss exeC Users Owner AppData Local Temp Low notepad exeC Windows system wuauclt exeC Windows system taskeng exeC Users Owner AppData Local Temp Low Low win exeC Users Owner AppData Local Temp Low Low win exeC Users Owner AppData Local Temp Low Low login exeC Program Files BullGuard Ltd BullGuard BGScan exeC Program Files Internet Explorer IEXPLORE EXEC Program Files Internet Explorer ieuser exeC Program Files Trend Micro HijackThis HijackThis exeR - HKCU Software Microsoft Internet Explorer Main Search Page http go microsoft com fwlink LinkId R - HKCU Software Microsoft Internet Explorer Main Start Page http home mywebsearch com index jhtml pt amp n ce dR - HKLM Software Microsoft Internet Explorer Main Default Page URL http go microsoft com fwlink LinkId R - HKLM Software Microsoft Internet Explorer Main Default Search URL http go microsoft com fwlink LinkId R - HKLM Software Microsoft Internet Explorer Main Search Page http go microsoft com fwlink LinkId R - HKLM Software Microsoft Internet Explorer Main Start Page http go microsoft com fwlink LinkId R - HKLM Software Microsoft Internet Explorer Search SearchAssistant R - HKLM Software Microsoft Internet Explorer Search CustomizeSearch R - HKCU Software Microsoft Windows CurrentVersion Internet Settings ProxyOverride localR - HKCU Software Microsoft Internet Explorer Toolbar LinksFolderName F - REG system ini UserInit C Windows system winlogon exeO - Hosts localhost Inserted By STOPzilla O - Toolbar McAfee VirusScan - BA B -B - c -B - F F - c progra mcafee com vso mcvsshl dllO - HKLM Run readericon C Program Files Digital Media Reader readericon G exeO - HKLM Run Recguard WINDIR SMINST RECGUARD EXEO - HKLM Run Reminder WINDIR Creator Remind XP exeO - HKLM Run SunJavaUpdateSched quot C Progr... Read more

A:microsoft windows search protocol host stopped, slow, firefox doesn't work, itunes doesn't work

Hello and welcome to Bleeping ComputerWe apologize for the delay in responding to your request for help. Here at Bleeping Computer we get overwhelmed at times, and we are trying our best to keep up. Please note that your topic was not intentionally overlooked. Our mission is to help everyone in need, but sometimes it takes just a little longer to get to every request for help. No one is ignored here.If you have since resolved the original problem you were having, we would appreciate you letting us know. If not please perform the following steps below so we can have a look at the current condition of your machine. If you have not done so, include a clear description of the problems you're having, along with any steps you may have performed so far.Upon completing the steps below another staff member will review and take the steps necessary with you to get your machine back in working order clean and free of malware.If you have already posted a DDS log, please do so again, as your situation may have changed.Use the 'Add Reply' and add the new log to this thread.Thanks and again sorry for the delay.We need to see some information about what is happening in your machine. Please perform the following scan:Download DDS by sUBs from one of the following links. Save it to your desktop.DDS.scrDDS.pifDouble click on the DDS icon, allow it to run.A small box will open, with an explaination about the tool. No input is needed, the scan is running.Notepad will open with the results.Follow the instructions that pop up for posting the results.Close the program window, and delete the program from your desktop.Please note: You may have to disable any script protection running if the scan fails to run. After downloading the tool, disconnect from the internet and disable all antivirus protection. Run the scan, enable your A/V and reconnect to the internet. Information on A/V control HERE
Relevancy 58.05%

nvidia sys tool
changed the fsb overclock
system hanged
did a reboot
sys boot image corrupt
mgr corrupt ,boot image corrupt

i cannot reinstall windows as well,when i insert bootable usb windows 7,8.1(also the current os i am runnning )
it auto enters repair mode wihout any option before that ,then getting errors 0xc00001

there is no way i can proceed from here

fatality fp in9

A:nvidia fsb overclock,mgr corrupt ,boot image corrupt ,cannot reformat

If you can't get disk to boot try flash stick alternative provided in Step 6 of Troubleshooting Windows 7 Failure to Start which also has everything else that can be done to start Win7.

If that fail try resetting BIOS to defaults.
Relevancy 57.19%

Help my windows 7 laptop just keeps rebooting and i cant get to safe mode or recovery what should i do ?

A:system recovery doesn't work and safe mode doesn't work and just keeps reboting

System manufacturer and model?
Relevancy 57.19%

hi, I know there are many in the forum who have the same problem as mine. 
my computer was running fine last friday. I tried to start it on saturday, it says it can't startup and need to repair startup. I did run the repair but still can't startup. I tried to use system restore to earlier dates, it still can't startup. The computer has trojan virus before and I tried the anti-malware from internet to kill them. seems that it create more problem for my PC. I have some important files in the computer that I wish I have archived. 
wonder if any one can help. thx in advance.

A:can't start up computer-window7, repair doesn't work, restore doesn't work

I'll report this topic to appropriate helpers.
Hold on there...
Relevancy 57.19%

I am new here At first a happy new year to everybody Yesterday I bought the "Complete" version Image work. boot in 7.0 True doesn't of cd boxed version of True "Complete" version of boot cd in True Image 7.0 doesn't work. Image and installed it During the installing I also made boot disks as well as as a boot cd both in the quot complete quot version After that I tried to boot from the disks and also from the cd of course changed the bios to boot from cdrom "Complete" version of boot cd in True Image 7.0 doesn't work. Both didn t work My computer booted and I did get the start screen from Acronis but after that it said quot Loading Acronis please wait quot with the disks as well as with the cd After that nothing happened anymore even after minutes I made a new boot cd but this time a quot safe quot version and that DID work I assume however that because there are no usb drivers etc included you can t use it with an external usb drive or so Does anyone here have the same experience or a clue to solve it I already emailed Acronis but didn t get a reply yet probably because it s New Year Thanks in advance Ton nbsp

A:"Complete" version of boot cd in True Image 7.0 doesn't work.

No idea, but this is clearly something that Acronis chould be able to sort out.
Relevancy 57.19%

Hey y'all,

I downloaded Flashplayer 9 from adobe the other day and it was working fine until all of a sudden, out of the blue, no sound. I've got no clue!!! PLEASE HELP! WMP still works but, that's about it. Other sounds seem to not work in either IE or Firefox. I'm running XP. mp3s and such work outside of a browser, like I can download .wav and mp3s but, they won't play in my browser. Suggestions?

A:Sound in Flash is a Problem--It doesn't work, broken, dead--No Sound!

Have you tried re-installing Flash Player 9?
Relevancy 55.9%

On a Dell 2400, I received this blue screen message after reinstalling XP before the install completed. I first reformatted the hard drive and went through the normal steps, but now do not know how to correct this problem.
Relevancy 55.04%

I am trying to use my CD-ROM drive and it doesn't work here are the list of things I have tried

Uninstalled and reinstalled the cd-rom driver it is a Matbleepa UJ-840D CD-ROM/DVD/CD-RW in my HP laptop (Didn't work)

Read stuff about code 39 and removed in the registry edit screen Upperfilters, Upperfilters.bak, Lowerfilters, Lowerfilters.bak and rebooted (Didn't work)

Removed itunes from computer (didn't solve the issue with cd-rom player)

Went back to a system restore point that was before the last time I used the CD-rom player and it worked and that (didn't work as well)

Read a lot of different posts about code 39 and nothing is given after the above steps are taken if it still won't work except to reformat which I would prefer not to do.

Any help would be greatly appreciated.

A:CD-ROM doesn't work, code 39 error, tried many things still doesn't work

1. Uninstall the drive through Device Manager.Restart computer. The drive will be automatically reinstalled.or...2. Delete Upper & Lower Filters computer.or...3. Download, and run Restore Missing CD Drive patchDouble click on to unzip it.Right click on cdgone.reg, click Merge.Accept registry merge.Restart computer.or...4. Go to Device Manager, click a "+" sign next to IDE ATA/ATAPI Controllers.You'll see two items:- ATA Channel0 (or Primary Channel)- ATA Channel1 (or Secondary Channel)Right click on each of them, and click Uninstall. Confirm.Restart Windows. They'll be automatically reinstalled.
Relevancy 53.32%

Hi,My Lenovo laptop K2450 wont boot up and always in blackscreen (no boot, no bios, no lenovo logo or anything just blackscreen) when im turn on the power, this happen after im changing some config in BIOS (but tottally forgot what changed). Everything work fine except fan is off after 3 second. Already tried to reset BIOS but nothing happen, then my technician say that my BIOS is corrupt and i need back up for that. Anyone here got BIOS backup for Lenovo K2450? thanks for help.
Relevancy 53.32%

My harddrive recently failed and it cannot be recovered. However, now that the harddrive has failed, I can't put any harddrive or ssd in there even if they have working OS' installed. I even tried various OS' with bootable USB's. Freedos is the only OS that seems to run via USB.  I went through the hp support video: "How to update BIOS when windows does not run" but don't have the "Firmware Patching" option is not available as my update utility version is 3.3.7 rather than the 5.something version featured in the video. The exe provided(SP52604.exe) is... well and EXE! I need an iso or bin or something for freedos 1.0 to run it. I have tried using Freedos 1.1 which should run exe's however, I cannot find a bootable image of freedos 1.1 to put on usb.  What else can I do to flash the bios?
Relevancy 51.6%

Hello everyone I ama new user and i am coming up with this post as I couldn t find any kind of solution update BIOS B590 failure! Lenovo BIOS FLASH! Black... for my problem Recently I decided to do a reinstallation of my operating system which also previously was Windows Ultimate x The installation went as usual and after finishing it I went on to install all the latest drivers from the Lenovo site for my product When getting close to installing almost all the drivers i ve needed i Lenovo B590 BIOS update failure! BIOS FLASH! Black... stumbled upon a new version of the BIOS amnd the drivers and sfotware recommended for my laptop by the producer So i proceeded to install the upgrade restarted the computer when it prompted me to do so but after the so-called restart the laptop did not boot up as usual At first it was telling me to not do anything as the BIOS is being flashed and then it was telling me something about some sort of image processing things that i did not understand at the time i have never encountered anything like that After that my screen turned black I have not done anything for a few couple of minutes as i thought it was supposed to be like that but then i just force shut it down and unplugged the AC adapter When trying to boot it all up again the only thing i got was a black screen and nothing else After doing a little bit of research it appears that somehowm i ve managed to corrupt the bios on my laptop or something and nothing else would work at this point I tried to remove the BIOS battery and the ram and then put them all back tryed resetting the bios by taking out the battery but nothing would work I would be really thankful if anyone would be kind enough to point me one way or another as i do not know what to do at all nbsp Around the webz i found some way of creating a bootable usb flash drive where i would put a compatible version of BIOS from the site and then install it onto the laptop but i do not quite know how to do that properly either as the software they are pointing me to wincrisis is not working by any means
Relevancy 51.6%

Im working on a Toshiba Laptop A - Model PSAA U- FH K that froze while trying to flash the BIOS so I didnt know what won't A105: Failed access now BIOS & BIOS Toshiba flash; boot no else to do but shut it off Now when Toshiba A105: Failed BIOS flash; now no BIOS access & won't boot I Toshiba A105: Failed BIOS flash; now no BIOS access & won't boot try to boot it up it gets stuck in the same place it did during the flashing on the Toshiba splash screen with the status bar at the bottom showing about complete I cant get into the BIOS and cant boot into Windows Other options available on this screen are Press F for System Settings and F for Boot Menu Pressing F results in a beep and the status bar changing to quot Please Wait quot but nothing else happens no matter how long I wait Pressing F doesnt do anything Pressing ESC takes me to a screen that shows the typical system info -- Phoenix Technologies Version Intel Calistoga CRB T A Reference BIOS VERSION MAK looks like its running POST and recognizes CPU Cores No TPM or TPM has a problem and system RAM and stops there What is my best course of action - shorting out the CMOS battery I ve tried this on the solder pads marked C with no laptop battery with and without the wi-fi ram and hdd installed Im either doing it wrong or its just not working - trying to reflash BIOS chip I tried this turned the laptop on and held down the c key to boot from cd but still got stuck at the same place - replacing the BIOS chip - something else Any guidance or information you can provide would be greatly appreciated Please feel free to let me know if you need any additional info from me Thanks so much in advance NorCalGirl Toshiba Laptop A - Model PSAA U- FH K Windows MCE SP I believe -bit GB RAM nbsp

A:Toshiba A105: Failed BIOS flash; now no BIOS access & won't boot

Im trying to figure out why I've had no replies yet.

Have I asked a stupidly easy question that everyone is rolling their eyes to and cant bear to tell me the answer? Or have I stumped everyone?

I have a hard time believing this is a stumper. I've found the same question posted elsewhere on the net and shorting the CMOS seemed to help. That or removing the battery altogether (its soldered to the board), but I dont think Im doing it right. Can someone give me directions on that?

or is this just a lost cause? :-/

Thanks in advance
Relevancy 51.17%

Hi There,

I just built a desktop with a sabertooth x79 motherboard, and am running Windows 8.1 pro 64-bit. When I click the UEFI BIOS Firmware live tile via the change PC settings>update and recovery>recovery>etc. my computer reboots normally to Windows and will not open BIOS. I have tried accessing it using the delete and f2 keys, but this does nothing either.

Any ideas? I am up to date in terms of my BIOS, and am definitely running UEFI and not legacy.

Thank you so much.

A:UEFI BIOS firmware restart doesn't boot to BIOS

Motherboards - SABERTOOTH X79

Originally Posted by ASUS
Relevancy 51.17%

I have an Asus A8N-E mobo and want to flash my bios, however like I said, the Award flash utility is nowhere to be found. So how do I do it?

Relevancy 50.74%

I have a five-month old HP Compaq Presario Laptop, which has been working fairly decently (I've had a few virus scares, and my Norton quarrentined something a twenty days ago). On HP's advice, I just updated the BIOS on my laptop. It's currently stuck at Verifying New Bios Image, and it's at 100% - It's been stuck that way for a half-hour plus. Any advice? What should I do?

A:HP BIOS Update Stuck at "Verifying New Bios Image 100%"

You have no choice but to force a reboot and keep your fingers crossed.
Relevancy 50.74%

I have no idea what my sister and her friends were doing on the comp for a couple recov not work computer shut down loading right, sys right, doesn't programs doesn't of days that i decided not to use it but now - a few programs take forever to load or don't load at all but they do show up under the processes tab in the task manager - after pressing Ctrl Alt Del the task manager icon appears in the system tray but the thing only shows up a minute later - my system recovery is quot not able to protect my computer quot and restarting does nothing - actually when restarting or shutting down Windows it stops at where it only shows my desktop background and cursor which is still able to move and nothing else after that so i have programs not loading right, computer doesn't shut down right, sys recov doesn't work to hold the power button and force it to shut off - when I right click the desktop and click on quot Properties quot or something similar to programs not loading right, computer doesn't shut down right, sys recov doesn't work this action it doesn't show up at all and whenever I try to open any application after that they don't even load at all either - and probably other stuff that I haven't took note of yet Things i've tried to get rid of these problems - Virus scan with programs not loading right, computer doesn't shut down right, sys recov doesn't work avast a couple viruses found and fixed but nothing changed - disk clean up nothing changed - registry clean nothing changed - CURRENTLY defragging my C drive hope something changes Anyone know what the heck's going on Anyone got any suggestions on what to do next Anything helps and would be greatly appreciated

A:programs not loading right, computer doesn't shut down right, sys recov doesn't work

no replies yet? :(

anyway, just stopped by to say that when shutting down, it takes forever to get to the "Saving your settings..." screen, and that's where I decided that it stops and nothing else after that.
Defragged my C drive, still no results besides the computer feeling a bit smoother-running o_o
Relevancy 50.74%

I have an ASUS notebook running windows 7 64-bit. I am using the QuietOffice power profile, however the screensaver won't kick in no matter what I do, and the display does not turn off even though I set it to be after 5-minutes of inactivity. I don't know if there is something running in the background... I have turned off my usb wireless mouse, and nothing....

Any ideas?


A:HELP: power option doesn't work - screen saver doesn't start!

This is another case of factory bloatware interfering - in this case a useless factory utility overriding Win7's superior built-in version.

Googling the Quiet Office feature of Asus there are multiple reported problems. Best to default to the Win7 built-in Power Options in Control Panel. Set up a Balanced Plan unless you're a gamer then use High Performance.

Here are other tips for cleaning up factory bloatware
Relevancy 50.74%

I have a 4y old Sony VAIO (VGN-NS11J) that stopped working today morning after making a whirring noise

Repeated attempts to restart failed and after many attempts, I managed to get to the Startup Repair mode - after a long time, startup repair says it failed to automatically repair the problem

I managed to run system restore but after a while I got the following message: "System restore failed due to an unspecified error. The disk strucgture is corrupted and unreadable (0X80070571)

My laptop did not come with a Windows Vista CD/Recovery disk

My first priority is to recover a few files in the laptop - if I am able to do this, then I dont mind junking the laptop

Since this is an old laptop, I would prefer not to use an expensive professional to recover the data

Any help/suggestions would be much appreciated!


A:Sony VAIO running Vista doesn't start-up, system restore doesn't work

You may be able to retrieve your data by using Ubuntu. Post #3 in this topic provides instructions.
Relevancy 50.31%

For the last month or so, every time I log off my account, the keyboard does not register at the Windows Log In screen. This makes it so I have to restart the computer and then it works fine.
There are three accounts on the computer, the casing has been half removed for the last 3 months, a DVD burner and driver recently installed 3 months ago and I am using a wireless off brand USB keyboard and mouse.
OS: Windows Xp Home Edition 5.1.2600 Service Pack 3
As for the second part, the computer requires several restarts to boot up, sometimes up to twenty minutes of turning on and off to boot up. Only started doing this a week ago.

A:My Keyboard doesn't work, and the computer turns on but doesn't start.

It sounds like something is wrong with your Windows XP drivers. Something like that happened to me while building my computer, and when I boot up the keyboard did not work because my copy of windows XP was bad. You could try reinstalling windows XP, and It might work better, but I dont have a definite answer to your problem.
Relevancy 49.88%

lenovo 7360  link bios
Relevancy 49.88%

Cant get it to updateand when i use thr troubleshooternit doesnt work either Farbar Service Scanner Version - - Ran by Administrator doesn't doesn't troubleshooter and work 7 update Windows administrator on - - at Running from D Users Administrator Downloads Microsoft Windows Ultimate Service Pack X Boot Mode Normal Internet Services Connection Status Localhost is accessible LAN connected Google IP is accessible Google com is accessible Yahoo com is accessible Windows Firewall mpsdrv Service is not running Checking service configuration The start type of mpsdrv service is OK The ImagePath of mpsdrv service is OK MpsSvc Service is not running Checking service configuration The start type of MpsSvc service is set to Disabled The default start type is Auto The ImagePath of MpsSvc service is OK The ServiceDll of MpsSvc service is OK Firewall Disabled Policy System Restore SDRSVC Service is not running Checking service configuration Checking Start type ATTENTION gt Unable to open SDRSVC Windows 7 doesn't update and troubleshooter doesn't work registry key The service key does not exist Checking ImagePath ATTENTION gt Unable to open SDRSVC registry key The service key does not exist Checking ServiceDll ATTENTION gt Unable to open SDRSVC registry key The service key does not exist Windows 7 doesn't update and troubleshooter doesn't work System Restore Disabled Policy Action Center Windows Update Windows Autoupdate Disabled Policy Windows Defender WinDefend Service is not running Checking service configuration Windows 7 doesn't update and troubleshooter doesn't work The start type of WinDefend service is set to Demand The default start type is Auto The ImagePath of WinDefend service is OK The ServiceDll of WinDefend service is OK Windows Defender Disabled Policy HKEY LOCAL MACHINE SOFTWARE Microsoft Windows Defender DisableAntiSpyware DWORD Other Services File Check D Windows system nsisvc dll gt MD is legit D Windows system Drivers nsiproxy sys gt MD is legit D Windows system dhcpcore dll gt MD is legit D Windows system Drivers afd sys - - - - - - A Microsoft Corporation D B DA D A E EB A DD D Windows system Drivers tdx sys - - - - - - A Microsoft Corporation FE A DFA C A E AE C AAB D Windows system Drivers tcpip sys gt File is digitally signed D Windows system dnsrslvr dll gt MD is legit D Windows system mpssvc dll gt MD is legit D Windows system bfe dll gt MD is legit D Windows system Drivers mpsdrv sys gt MD is legit D Windows system SDRSVC dll gt MD is legit D Windows system vssvc exe gt MD is legit D Windows system wscsvc dll gt MD is legit D Windows system wbem WMIsvc dll gt MD is legit D Windows system wuaueng dll gt File is digitally signed D Windows system qmgr dll gt MD is legit D Windows system es dll gt MD is legit D Windows system cryptsvc dll - - - - - - A Microsoft Corporation CA BECEA DE ADDAD E A C D Program Files Windows Defender MpSvc dll - - - - - - A Microsoft Corporation CF F FAE DE AD EB D Windows system ipnathlp dll gt MD is legit D Windows system iphlpsvc dll gt MD is legit D Windows system svchost exe gt MD is legit D Windows system rpcss dll gt MD is legit End of log Edit Topic moved from Windows to the more appropriate forum due to FRST log Animal

A:Windows 7 doesn't update and troubleshooter doesn't work

Please follow the instructions Here to run the System Update Readiness Tool. When the SURT finishes installing, copy (Ctrl + C) and paste (Ctrl + V) the contents of the SURT log into your next post please:C:\Windows\Logs\CBS\CheckSUR.logC:\Windows\Logs\CBS\CheckSUR.persist.log
Relevancy 49.88%

Have a friend with a relatively new Lenovo laptop using Windows XP SP3. Overnight he can't access the Internet via browsers, email or AIM. His desktop connected to the same router is working fine.

He can access the router by IP address using either IE7 or FireFox 3.5. Anything that needs a DNS server doesn't work. This does say though that he has a working connection to the router.

He's run MalWareBytes and his own McAffee software looking for bad stuff but has found nothing.

Running "ipconfig /all" from the command prompt gives exactly the same results for the laptop as his working desktop. The DNS servers are there. He can ping the DNS servers using their IP addresses. He is being assigned a proper local network address so DHCP is working on the router.

Any thoughts on where to look next to discover why the Internet applications don't seem to be able to find the DNS servers?

A:Can't Access Websites, Email doesn't work and no AIM doesn

FWIW, my friend took his laptop to a PC shop. Their diagnosis was malware. I don't know the identity of the malware. Anyway, the shop saved his data then formatted and reloaded XP SP3.
Relevancy 49.88%

I am quite new here, but I've been wanting to get this problem solved for a long time, and I haven't seemed to get any answer.

So here's my problem:

I bought my Asus N53SV for around a year ago, and it worked great. But for some reason something changed.
When I try to open bluetooth, nothing happens. And when I want to connect anything using bluetooth, it doesn't work.

I tried to do this:
[windows] + r >bttray
But nothing opens up.

Please help!

Thank you,

A:My bluetooth doesn't work. bttray doesn't open.

Quote: Originally Posted by Karstin1812

I am quite new here, but I've been wanting to get this problem solved for a long time, and I haven't seemed to get any answer.

So here's my problem:

I bought my Asus N53SV for around a year ago, and it worked great. But for some reason something changed.
When I try to open bluetooth, nothing happens. And when I want to connect anything using bluetooth, it doesn't work.

I tried to do this:
[windows] + r >bttray
But nothing opens up.

Please help!

Thank you,

Hi Karstin,

Welcome to Seven Forums.

You would need to re-install Bluetooth software/driver for your system. Please check the link below for finding out the drivers:

ASUSTeK Computer Inc. -Support- Drivers and Download

If you have any further queries, please feel free to contact us.
Relevancy 49.45%

I took some photos on a recent snowboard trip to France and on return have found that one of the pictures is showing file error when I try and view it via the camera and when transferred to the computer the JPEG opens with a red cross and says no preview available I have tried opening the file with various different HELP! Corrupt - Image programs and have also attempted to use some file recovery software obtained via the web but to no avail The closest Corrupt Image - HELP! I have come was using some software called quot JPEGSNOOP quot http www impulseadventure com photo Corrupt Image - HELP! jpeg-snoop html through this I managed to recover Corrupt Image - HELP! a blurred image however my lack of computer literacy stopped me from going any further in recovering the full image I was wondering if anyone had any knowledge suggestions that they would be able to offer I have attached the JPEG file if someone would like to have a go The picture was taken using a Samsung D Camera and a SanDisk SD memory card GB Many thanks nbsp

Relevancy 49.45%

I couldn t find a BIOS category so I figured HDD: BIOS BIOS doesn't Virus? detect this forum BIOS doesn't detect HDD: BIOS Virus? was the closest fit with my problem In a nutshell my Dell Dimension BIOS is BIOS doesn't detect HDD: BIOS Virus? claiming my drive that has been working without incident for a year is suddenly quot not installed quot I ve been using a Dell Dimension P GHz for a couple of years without problems One of my other computers randomly decided to stop working another story altogether so I used the Dell to BIOS doesn't detect HDD: BIOS Virus? do analysis on the drive Since it was a SeaGate hard drive I used SeaGate s online scanner to scan it for errors because I suspected it was faulty I also did some virus scans I restarted a little while later and the Dell computer would get stuck on the Dell post screen It wouldn t even go into BIOS after I hit DEL it would freeze So I flashed the BIOS A from Dell s website after reading some threads stating that maybe I had screwed up the BIOS I was really confused as to why things were messed up I still had the same issue where it would get permanently stuck after the memory testing on the post screen and wouldn t let me access the BIOS I did some more reading and read that hardware components could be messing up the computer load process It turns out my CD-Rom drive was faulty or something so when I removed it BIOS was accessible However now I faced a new problem BIOS doesn t recognize the original drive that was in the Dell which is connected to a PCI slot via a Promise Ultra TX ATA controller card So Windows won t load because my computer doesn t think there s a drive installed The Dell tries to load PXE and other networking stuff but of course fails Oddly the screen following the ATA card detection process after post and BIOS loading the computer lists all the IDE devices and properly identifies HDD- as a Maxtor mb drive which it is The Dell BIOS is pretty limited in customization In the past it has always successfully detected installed hardware Under IDE Configuration my other CD-ROM is listed the one that isn t faulty but under HDD- it says quot not installed quot I chose auto-detect I tried the drive in question on another computer on the IDE motherboard slot not through a controller card and it is recognized just fine I can t use this drive directly on the Dell s motherboard IDE slot because it s an old computer and I will get data corruption since the drive is larger than GB I figured that issue out long ago I updated the BIOS with the ATA controller card BIOS upgrade file from Promise s website The jumper settings are set to Master I ve swapped IDE cables PCI slots and power cables Ooops while I was tying this I restarted the computer after switching PCI slots for the ATA controller card and now when I restart I get a black screen that says quot Invalid Boot Diskette Insert BOOT diskette in A quot There is no disk in the floppy drive Could I have a BIOS virus Does something like that exist Could that be why the drive on the other computer failed and then the CD-Rom drive on the Dell and now this error Thanks for any help and I apologize if this is rather long-winded nbsp

A:BIOS doesn't detect HDD: BIOS Virus?

Promise Ultra TX2 ATA controller card sounds faulty to me.
Try moving it to another PCI slot
Try CS instead of Master (even though it has worked on Master before)
Try resetting the bios jumper
Try dispersing all voltage to the M/b by holding the power button in for 30 secs whilst the power cable is out
Lastly test with another ATA controller card
Relevancy 49.02%

I have an HP laptop.  It originally came with Windows 7 but was upgraded to Windows 10 a few months ago.  It has been running fine.  I didn't use it for about a week.  When I went to turn it on today it came up with a black screen and the message "BOOTMGR is image corrupt.  System cannot boot."  I've looked online for answers, but can't quite seem to figure out what to do.  Has this happened to anyone else?

A:BOOTMGR image is corrupt

Hi,run a hard drive test and tell me the result  power down the note book as soon as you hit the power button , keep tapping the esc key on the top left corner until a new window opens up(the start up menu ) choose the option f2 and choose the option component test and then choose hardrive testcheers,Dhee
Relevancy 49.02%

I have had my comp for almost a year now, but it started to froze every time when it finished loading windows. So i reformat the HDD, ever since i have been trying to install windows i got errors. I kept doing the reformat process and now it only says when i try to install windows "The image ntvdm.exe is possibly corrupt. The Header checksum does not match the computer Checksum" been having this prob for a week now. Though i could fix it my self, but now i really need advice. Need to do so much work in my computer but cant cause I'm having this problem. Any kind of help would be nice

A:The image ntvdm.exe is possible corrupt

You need to run chkdsk /r from Recovery Console:
Relevancy 49.02%

Bootmgr image is corrupt

my child is getting this when stating her laptop, it was a second hand laptop i bought a couple of months ago ,i have tried the recovery disc and then got this

The file or directory D:\Windows.old is corrupt and unreadable. please run the CHKDSK utility. Which it looks like vista was on before windows 7 ,is there a fix for this thanks

i just run command prompt and got tgot this in the command promp

the type of the file system is NTFS

Chkdsk cannot run because the volume is in use by another process ,Chkdsk may run if this is dismounted first,
all oppened handlesto this volume would then be invali
would you like to force a dismount on this volume <Y/N>

so do i force a dismount ?

A:Bootmgr image is corrupt

What recovery disk? THe Recovery DIsks are to restore WIn7 to factory condition, used as a backup to the more stable method which is running the Recovery Partition from Win7 or boot using it's hotkey.

To Repair Win7 when it will not boot, use System Recovery Options preferably from the DVD or REpair CD. BOot in to accept any offered repair. If Win7 fails to start at reboot, boot back in to run Startup Repair repeatedly.

Startup Repair will automate System Restore, System File Checker and Disk Check, but if it fails try them manually from the Recover Tools list there. Run SFC or Disk Check from a COmmand Line: SFC -SCANNOW Run in Command Prompt at Boot

Post back the results. You may be able to delete windows.old archive if not needed, as well as back up stranded files, using this method: Copy & Paste - in Windows Recovery Console
Relevancy 49.02%

Please god help me with this someone! when i try and boot XP it goes directly to a blue screen and in white writing it says " c0000221 Bad image checksum. Image url.dll is possibly corrupt. The header checksum does not match the computed checksum" I have run diagnostics through the boot utility and nothing shows up. If someone could please help me with this it would be greatly appreciated. Use as much detail as possible with your help as i am alright with navigating the computer but definently not an expert.

Relevancy 49.02%

I am getting an error message The image wow32.dll is possibly corrupt--blue screen of death upon startup. I have a feeling my hard drive has crashed but am open to any possible suggestions. I have tried "last known good configuration (which very seldom seems to work anyhow)" and have tried booting into safe mode. No luck. I tried the hard drive on another PC, exact same kind, no luck. Anyone have any other ideas as to how I can try to correct this possible corrupt dll file or should I trash the hard drive. I am going to try getting into it as a slave but haven't done that just yet. Any suggestions or help would be appreciated.

A:Image wow32.dll is corrupt

You can do 3 things in a situation like this.
1. You can try a repair install
2. You can try to replace the files using your windows disk
3. You can set it up as a slave

Pick your choice and ill tell you how.
Relevancy 49.02%

Acronis says the image on these five DVDs is corrupt and will not do an image restore. If I copy all the five DVDs to a hard disk, the image restore goes without any problem.

What is going on here?

The DVD drive from which I am doing the restore is the one that originally created the image; but, just to be sure the DVD drive is not the problem, I tried the operation with another known-good DVD drive and the result is the same.

Relevancy 49.02%

Hi, new here.
So I have had this problem for a while generally just happens when i am playing games that require some power, I am to believe this is a hard drive problem. ok so sometimes my computer will blue screen out or i could even shut it down as normal, but both end with the same result and the computer cannot load back up ' BOOTMGR image is corrupt, system cannot boot' something along those lines.
Also alot of my files seem to be going corrupt for no reason, but when left for a while ( couple of hours ) they will work again.
if anyone knows anything about this problem or needs more info on my pc etc please post.

A:BOOTMGR image is corrupt

It probably is your hard drive. See if you can find a Ultimate boot disk or some type of disk check from your manufacture of the drive and run diagnostics on the hard drive. If it comes back with a bunch of corrupt clusters get as much data off as you can.
Relevancy 49.02%

I get this message regardless of the bootable drive i select. I installed a new hard drive and tried to boot from my Windows system recover disk (DVD drive) and still get this message. I also reset my bios to the factory default. Nothing worked. Is there a way to fix the Boot MGR Image?


A:BootMGR image is corrupt

Hi and welcome to TSF please see the info here Use the Bootrec.exe tool in the Windows Recovery Environment to troubleshoot and repair startup issues in Windows
Relevancy 49.02%

A computer AthlonXP with XP Home Image Corrupt Ghost SP used by four family members decided three weeks ago to start crashing with random BSODs up to per day I analyzed dozens of Minidump logs and found nothing that could be pointed to as the cause After verifying no viruses or spyware swapping RAM video card and PSU and all of the other tricks I know including a repair install which failed three times I decided to load my last saved Ghost Image which greeted me with a decompression error - image file is corrupt At that point I decided to do a clean install of XP which also failed several times at and minuted to completion I decided either the MOBO or CPU were bad so I drove over to Fry s Electronics and bought an Asus P GC-MX Corrupt Ghost Image mobo E CPU GB DDR - RAM GT video card Antec W PSU Corrupt Ghost Image and XP Pro OEM I got that working with my old hard drive and DVD burner and told my family to have fun reinstalling programs Now I am no longer interested in restoring the corrupt Ghost image but I would like to recover data from it email pictures documents The image made with Ghost contains a GHS and GHO files At least one of the GHO files is corrupt Is there a way to recover anything at all from the others nbsp

Relevancy 49.02%

Hello Looking for a little help I recently increased the speed of my memory via the BIOS to take full advantage of my OCZ Gold DDR x gb memory memory is currently my biggest performance hurdle and more is being sent via fedex BOOTMGR is image corrupt The BIOS of the Biostar GXE M defaults the speed of the memory to mhz and I was BOOTMGR image is corrupt attempting to update it to This was completed successfully and upon restart Windows Professional x hung upon a page that said quot Loading files quot with a progress bar at the bottom The progress stopped at fully complete and sat for hours before I finally turned the PC off Upon reboot I received a quot Bootmgr image is corrupt The system cannot boot quot message I reset the memory back to mhz restarted and received the same quot Loading Files quot page but this time it stopped at about half way through I again rebooted the PC and received the same quot Bootmgr image is corrupt The system cannot boot quot message to the same error again and again Following various other advice from this forum I have downloaded the proper ISO file and used the Win USB DVD Download Tool to burn the ISO to a DVD to attempt to repair I have verified that the BIOS is setup to load the USB then DVD then HDD win is on the HDD not SSD Upon entering the DVD and restarting I receive a prompt that says quot press any key to boot from the DVD quot which I do Windows then brought up a quot Loading Files quot prompt with progress bar that never finishes I restarted again received the same prompt for quot press any key to boot from the DVD quot and upon pressing any key I now get quot BOOTMGR image is corrupt The system cannot boot quot I am scratching my head at this point Any help would be most appreciated Thanks Adam Biostar GXE M AMD Phenom II x Black ghz OCZ Gold Edition x GB pin DDR SDRAM DDR PC Win pro x Seagate Barracude gb HDD OCZ Vertex Plus R gb Sata SSD EVGA G-P - -KR GeForce GTX Ti CORSAIR CX series CX W ATX V v PLUS BRONZE

A:BOOTMGR image is corrupt

Attachment 299485

After rebooting and attempting to load the DVD, I got this message once. No clue what it means or if it points anyone into a helpful direction. It means jibberish to me.

Relevancy 49.02%

Hey all about a week ago I had a problem with an image I made I was making some graphics and decided to Corrupt Image File rename the file name This resulted in me not being able to open the file with any graphics program Windows Picture Viewer said No preview available Click to expand MS Paint said Paint cannot read this file This is not a valid bitmap file or its format is not currently supported Click to expand GIMP said This file is corrupted Click to expand The image format is PNG and I don t have Vista unlike the other people reporting Corrupt Image File this problem Recently I opened the file in IrfanView which loaded about of the image and left the rest of it black - which is some progress I guess Now atleast I can change the image format to pretty much anything e g JPEG but it still doesn t solve anything Any ideas on how I can repair the image Corrupt Image File I ve tried restoring my computer to an earlier time but to no avail E Forgot to mention I renamed it back to it s original name and still nothing nbsp

Relevancy 49.02%

Hi, I was letting my friend use my flashdrive, and I think he pulled it out to early, and now it is corrupt. I'm using vista i have service pack 1, and all it says when i plug it in is unknown device not recognized.. It says the same thing in device manager, unknown device.

A:Flash drive corrupt HELP

Plug it in Vista and then delete the unknown device and then scan for hardware changes this should allow Vista to reisntall it. If not it's likely hosed. You could always try installing it in a differnt PC and reformat it there.
Relevancy 49.02%

Hi safemode reboot, XP work doesn't doesn't xp stopped responding and I decided to power off Was never able to restart after that Normal boot shows the windows initial screen but eventually just restarts safe mode does the same thing whether it s with network XP doesn't reboot, safemode doesn't work command line or plain safe mode Last known good configuration does the same Needed to use a file so decided to remove the HD and re-install to another PC I did have access to the file in question but now I d like to fix the problem The other system uses AVG I started a scan and it detected Cekar d A exe wdfmgr exe and initially ntldr exe Dropper Inor ntdetect hta A hta PSW Generic ABVW ctfmona exe PSW OnlineGames AAFI ctfmonb exe PSW Generic AFYK ctfmond exe PSW OnlineGames ZWT LotusHlp exe and some others but for whatever reason the scan stopped I restarted it and now the AV still finds most of the threats it was seeing before but not Cekar d in the ntldr exe file The system that had the problem was running Win XP Home SP Unfortunately I can t find the manufacturer s recovery CD HD is still in the other PC How should I attack the problem nbsp

A:XP doesn't reboot, safemode doesn't work

Update... Three passes of AVG and all threats were put in vault. Tried to re-install the HD to the initial system but no change... System says it didn't start correctly, that a new software of hardware could be responsible, the suggests to try las known good config, none of the options work, they all perform some tasks then windows reboots and ends up in the same screen.
Relevancy 48.59%

Acer aspire's Bluetooth doesn't work since I bought it I've installed drivers too but it doesn't work what should I do.
In its specs it has Bluetooth . But there is no Bluetooth device found in device manager how to repair this.
Please HELP!!

A:acer aspire 4738' s bluetooth doesn't work but wifi work?

Hi ... Welcome to Seven Forums ... What is the Model Number of your Laptop ? ...

Did you buy the Laptop from new ? ...
Did you mean Windows 7 x86 ?...
If your System Specs are correct you have 4 GB of ram ? ...
If that is the case your Windows should be 64 Bit ...